Weeds between pavers and driveway joints: why they keep coming back in Cairns and what actually stops them
By Trisim Property Maintenance, CairnsLast reviewed
- 12 min read
- 14 sources checked
- 7 questions answered
Weeds between pavers grow from seed that lands in the joints, mostly where the jointing sand has washed low. Scalding the leaves or pouring home remedies on them mostly clears the top growth. What lasts is getting the weeds out by the root, then refilling the joints firm and full with clean jointing sand or polymeric sand so seeds have far less room to settle.
Pouring something on the leaves treats the weed and leaves the gap it lives in. Paver manufacturer Unilock describes the problem the other way round: weeds grow where jointing sand washes away and leaves space for seed. A joint in that state will keep growing weeds until the joint itself is fixed.
Cairns makes this worse than most places. Heavy wet-season rain moves loose joint sand, and the pressure washing that clears black growth from paths can take joint sand with it. This guide covers why joints empty out, how to get weeds out properly, what to refill with, and the rules about what can go down the gutter. For what vinegar, boiling water and salt do as weed killers, see our guide to natural weed control. Trisim does not spray weeds; our part is high pressure cleaning of driveways, paths and patios.
Why weeds grow between pavers: seeds land in low, washed-out joints
Weeds between pavers start from seed that lands in the joints. Paver manufacturer Unilock puts it plainly: weeds do not come from underneath the pavers; they come from seeds that blow in and fall into the joints and germinate. Its weed guide adds the condition that lets them in. Weeds grow between the stones when the jointing sand washes away and leaves space for seedlings to fall in, and down in that moist, dark gap the conditions are right for them to germinate and grow.
The Royal Horticultural Society in the UK says the same of paths, patios and driveways generally: the weeds are often blown in as seed, and creeping weeds can also spread onto paving from an adjacent lawn or border. That second route matters on Cairns properties where a nutgrass lawn runs right up to the paving. Brisbane City Council's weed tool describes nutgrass spreading by creeping underground stems with small tubers, and lists footpaths among the places it is a very troublesome weed.
The RHS also notes a safety point that goes beyond looks: weeds in areas of foot traffic can make the ground uneven and slippery when wet.
Why Cairns paving joints empty out: heavy rain moves loose sand
Paving joints in Cairns have a lot of water to survive, because so much rain falls in a short season. Bureau of Meteorology figures for Cairns Aero show mean rainfall of 404.8 mm in January, 436.1 mm in February and 424.3 mm in March, out of 2,019.1 mm for the year. Unilock says regular jointing sand is prone to erosion from heavy rain and runoff.
By Unilock's account, regular jointing sand needs topping up over time, while activated polymeric sand bonds to the pavers and resists erosion even in heavy rainfall. Water that sits on paving makes things worse. Unilock advises that paving should slope so rainwater runs off and stagnant water does not encourage weed and moss growth, and it warns never to put plastic under pavers, because that keeps the joints wet and makes weeds grow faster.
Unilock notes that moss generally develops in shaded areas that are slow to dry after rain. Our guide to black mould on driveways and paths covers cleaning the surface itself.
Does pressure cleaning make weeds between pavers worse? It can, unless the joints are refilled
Pressure cleaning can make weeds between pavers worse if the jet strips sand out of the joints and nobody refills them, because an emptied joint is exactly where new seed settles. Unilock's guidance treats lost joint sand as something to avoid while washing and to fix afterwards. Unilock's cleaning guide says to use a fan spray and angle the stream so you do not blow the sand out of the joints. Its FAQ warns against running the washer on high power or too close to the surface, and says that if some jointing sand washes out, you may need to sweep in new sand.
The refill step is simple. If the joints look low after pressure washing or heavy rinsing, Unilock says to let the area dry fully, then sweep clean sand across the surface to fill the gaps. It also notes that tight joints resist weeds. The order matters: wash, let it dry, then fill.
Washing is still worth doing on a slippery path. The point is that a wash on its own is half the job when the paving has sand joints.
How to get weeds out of paver joints, roots and all
Getting weeds out of paver joints for longer means removing the roots and the old joint material, then refilling. Unilock's method for established weeds is to pull the large weeds by hand first, clear the old sand out of the joints, let the surface dry and refill with jointing sand. Put together with the RHS advice on tools, the job runs like this:
- 1Pull the large weeds out by hand.
- 2Run a block paving knife or weeding knife along the joints. The RHS says the blade severs roots and the hooked end levers weeds out.
- 3For a deep-rooted weed you cannot get out of a narrow joint, keep cutting it back. The RHS says repeated removal of top growth weakens it and may eventually kill it.
- 4Clear the old sand and debris out of the joints. Unilock's method uses a pressure washer for this, on a low setting and not too close to the surface.
- 5Let the paving dry completely.
- 6Sweep in fresh jointing sand, or polymeric sand if it suits the paver, until the joints are full.
- 7Keep sweeping. Unilock recommends sweeping regularly so new seedlings cannot take root, and says a leaf blower also clears away debris and seed.
The RHS says weed burners are not ideal: it lists the fire risk, the need for fuel or power, and limited effect on deep-rooted perennial weeds.
What to put between pavers to stop weeds: joint fillers compared
Nothing stops every weed for good, but a full, firm joint gives seed far less to grow in than a low, washed-out one. These are the main options paver manufacturer Unilock describes, with what each does and the trade-off:
- Regular jointing sand on its own: fills the joint and holds the pavers in place. Trade-off: Unilock says it erodes more readily, weeds can still find their way in, and it may need more frequent top-ups, especially on wider joints or steeper surfaces.
- Regular jointing sand plus a joint sand stabilising sealer: Unilock says this combination helps prevent joint sand washout and protects against weed growth. Trade-off: the sand must be dry before sealing, and it is a second product to apply.
- Polymeric sand: sand with polymers and binders that sets once wetted. Unilock says it resists erosion even in heavy rain and makes a nearly airtight seal that significantly reduces the risk of weed growth. Trade-off: it needs a dry surface and careful activation, and it does not suit every paver.
- Leaving low joints and treating the weeds: no new material to buy or lay. Trade-off: seed keeps landing in the gap, so the weeding never ends.
If the problem is a garden bed next to the paving rather than the joints themselves, our guide to weed mat under mulch covers that side.
Polymeric sand reduces weeds, but only when it goes in dry and suits the paver
Polymeric sand reduces weeds between pavers when it is installed to the maker's instructions, and it can fail when it is not. Unilock describes it as a mixture of coarse sand, polymers and binding agents that is swept into the joints dry and activated with water after the joints are filled. Its own claim is that activated polymeric sand makes a nearly airtight seal that significantly reduces the risk of weed growth. Expect fewer weeds, and still the odd one to pull.
Installation is where it goes wrong. Unilock says the surface must be completely dry before water is introduced, and that activation means misting in passes rather than flooding, so the water does not wash out corners or leave sand streaks. Excess sand left on the face can activate and harden there, which is hard to remove. Check the bag for the joint width and compaction steps the product calls for. Compatibility matters too: Unilock does not recommend polymeric sand for its heavily textured stones. In a Cairns wet season, that means waiting for a properly dry spell rather than a gap between showers.
Boiling water, vinegar and salt in paving joints: short-lived, and salt harms the paving
Home remedies poured into paving joints mostly kill the leaves of small weeds, and salt damages the paving itself. Each one in a line, with more detail in our natural weed control guide:
- Boiling water: University of California IPM guidance says hot water is generally only effective on very small weeds, in sites such as paving joints, and is not very effective on perennials with rhizomes or bulbs. University of Illinois Extension notes the roots underground stay protected.
- Vinegar: Illinois Extension says the bottle in your kitchen is likely not a strong enough grade to work as a weed killer.
- Salt: Illinois Extension says salt destroys soil structure and moves into nearby areas, damaging plants. Queensland Government salinity guidance says salt corrodes and destroys the properties of bitumen, concrete and brick, which is the paving and edging you are trying to keep.
- Homemade mixes of vinegar, salt and dish soap: Illinois Extension points out they carry no label with safety or rate information, yet can still be hazardous.
None of these refills the joint, so the next seed that blows in finds the same gap.
Keep wash water, joint sand and weed killer out of the street gutter
Wash water, washed-out sand and weed killer should not go into the street gutter or a stormwater drain, because Queensland law treats all three as water contaminants. Schedule 10 of the Environmental Protection Regulation 2019 lists prescribed water contaminants that include chemicals such as herbicides, sediment, gravel and stones, and waste water generated from outdoor cleaning. Section 440ZG of the Environmental Protection Act 1994 says a person must not unlawfully deposit a prescribed water contaminant in a roadside gutter or stormwater drainage, or leave it where it could reasonably be expected to wash into one.
On a sloping Cairns driveway that means planning where the water and sand go before you start: sweep up the sludge rather than hosing it into the gutter, and keep runoff on the lawn or garden where you can. If you do buy a weed killer, the APVMA says registered products carry an APVMA or NRA approval number, and that you must read and understand the label before using any chemical. The label sets where and how a product can be used.
Grass in driveway cracks and pavers that have spread apart
Grass growing in a concrete driveway crack is the same problem as a weed in a paver joint: a gap that holds soil and seed. The RHS weeding knife method works along cracks just as it does along joints, and the same rule applies to what goes in afterwards. A crack or joint left open will grow weeds again.
Pavers that have drifted apart are a different issue. Unilock says pavers should not separate from each other, and that when they do, it points to an improper base or missing edge restraints around the perimeter. Topping up sand in widening joints will not hold for long if the edge is moving. Relaying pavers, rebuilding a base or fitting new edge restraints is work for a paving contractor, so stop at checking and photographing the problem. Runners creeping in from the lawn edge are an edging job; our guide to common lawn weeds helps identify what is coming across, and nutgrass in lawns and garden beds covers that one in particular.
Getting the driveway and paths washed in Cairns
Trisim pressure washes driveways, paths and patios across Cairns, and every job is quoted before it starts. Because pressure washing sits alongside mowing and edging for us, the lawn edges beside the paving can be done on the same visit. Trisim does not spray weeds or apply herbicides. If your paving has sand joints, mention it when you ask for a quote, and plan for the joints to be refilled once the surface is dry. For deciding between a DIY scrub and a contractor, see black mould on driveways and paths.
Our local rounds take in suburbs such as Bentley Park and Edmonton. See the high pressure cleaning page for how we work within the current water rules, or request a free quote.
Common questions from Cairns residents
Because the gap is still there. Paver manufacturer Unilock says weeds grow from seed that falls into the joints, especially where the jointing sand has washed away. Pulling the weed leaves a low, washed-out joint for the next seed. Clear the old material out, let the paving dry, and refill the joints with clean jointing sand or polymeric sand, then sweep regularly so seed does not settle.
It can, especially on a high setting or with the nozzle close to the surface. Unilock advises a fan spray angled so the stream does not blow sand out of the joints, and says some jointing sand may still wash out. If the joints look low afterwards, let the paving dry fully, then sweep clean sand across the surface to fill the gaps before weeds find them.
It reduces them rather than stopping them outright. Unilock says activated polymeric sand forms a nearly airtight seal that significantly reduces the risk of weed growth, and resists erosion even in heavy rain. It has to go into joints on a completely dry surface and be misted in passes, and it does not suit every paver, so check the bag and the paver maker's advice first.
It is a poor idea. University of Illinois Extension says salt destroys soil structure and moves into nearby areas, damaging plants. Queensland Government salinity guidance says salt corrodes and destroys the properties of bitumen, concrete and brick, so it attacks the paving and edging as well as the weeds. Salty runoff is also a chemical you should not send into the street gutter.
No. Queensland's Environmental Protection Regulation 2019 lists herbicides, sediment and waste water from outdoor cleaning as prescribed water contaminants, and section 440ZG of the Environmental Protection Act 1994 says you must not unlawfully deposit them in a roadside gutter or stormwater drain. Sweep up sludge and sand, and direct runoff onto lawn or garden where you can.
A block paving knife or weeding knife. The Royal Horticultural Society says to run the blade along the joints to sever the roots, then use the hooked end to lever the weeds out. For a deep-rooted weed stuck in a narrow joint, it says repeated removal of the top growth weakens it and may eventually kill it. Refill the joint afterwards so new seed has less room.
No. Trisim does not spray weeds or apply herbicides. We pressure wash driveways, paths and patios across Cairns, quoted before any work starts, and can do the lawn edges beside the paving on the same visit. If your paving has sand joints, mention it when you ask for a quote, and plan for the joints to be refilled once the surface has dried.
Sources
- Frequently Asked Questions About Unilock Products, Unilock. Accessed .
- How to Kill Weeds Between Pavers, Unilock. Accessed .
- Polymeric Sand Guide: Installation, Benefits and Pro Tips, Unilock. Accessed .
- Cleaning Stains From Pavers, Unilock. Accessed .
- Spring Paver Maintenance Tips, Unilock. Accessed .
- Weeds on hard surfaces, Royal Horticultural Society. Accessed .
- Pest Notes: Weed Management in Landscapes, University of California Statewide Integrated Pest Management Program. Accessed .
- Homemade herbicide considerations, University of Illinois Extension. Accessed .
- Impacts of salinity, Queensland Government. Accessed .
- Environmental Protection Regulation 2019, schedule 10, Queensland Government (Office of the Queensland Parliamentary Counsel). Accessed .
- Environmental Protection Act 1994, section 440ZG, Queensland Government (Office of the Queensland Parliamentary Counsel). Accessed .
- Understanding Pesticide Chemical Labels, Australian Pesticides and Veterinary Medicines Authority. Accessed .
- Climate statistics for Australian locations: Cairns Aero, Bureau of Meteorology. Accessed .
- Nutgrass, Brisbane City Council (Weed Identification Tool). Accessed .
Last reviewed by Trisim Property Maintenance. Rules and council services change, so check the source before you rely on a date or a fee.
Related services
Lawn mowing around Cairns
From the Knowledgebase
- Black mould on driveways and paths in Cairns: why it grows and how to remove it safelyWhy Cairns driveways and paths go black, why it matters for older residents, what not to use, and the water and runoff rules for pressure cleaning in Cairns.Read the article
- Does vinegar kill weeds? What natural weed control does in a Cairns garden, and what lastsVinegar and boiling water burn weed leaves but rarely the roots, and salt harms the soil. What each remedy does in a Cairns bed, and what lasts.Read the article
- Common lawn weeds in Cairns and Far North Queensland: how to identify themIdentify common weeds in a Queensland lawn, from nutgrass and crowsfoot to clover and khaki weed, and what some weeds say about wear, mowing and feeding.Read the article
- Nutgrass in a Cairns lawn or garden bed: why it keeps coming back and what actually controls itNutgrass regrows from chains of underground tubers, so pulling, plastic and quick sprays rarely finish it. What works in a Cairns lawn and in a mulched bed.Read the article
- Weed mat under mulch in Cairns: where it helps, where it harms and what to use insteadDoes weed mat stop weeds under mulch in Cairns? Why weeds root on top of it, where it still earns its place, and how cardboard and deep mulch compare.Read the article
Clean paving, full joints, fewer weeds
Tell us which driveway, paths or patio you want washed and whether the paving has sand joints, and we will quote the job before any work starts.